Always disconnect from the electrical socket before performing maintenance.
Always ensure the pump is submerged in water.
Do not lift the pump unit by pulling the wire (Power Cord).
The power supply cord provided for this appliance cannot be replaced.
If the power head is attached filter intake (with filter media) than a clogged or dirty intake screen will reduce the performance of the pump. Hence you must wash away the surrounded debris frequently.
Performing regular maintenance can prolong the life span of the pump. During Installation, ensure the power plug is inserted to the power socket outlet at the higher point. This is to ensure that water will not back flow via the wire to the socket outlet or via the air pipe
Maintenance : Remove the front cover and the impeller cover, followed by the impeller unit. use a small brush to clean the cylinder or just wash away the debris under running water.
Trouble Shooting : If the pump fails to operate, please check and ensure there is a consistent power supply to the pump unit.
Power : 25W
Voltage : 220-240V
Frequency : 50/60Hz
H.MAX : 1.5M
F.MAX : 1500L/H
Ideal for 350-400 liter aquarium tank.
Filter media / sponge (Sold separately) is not a part of this product.
Ceramic rings have long been used as filter medium in domestic aquariums.
Pores in the ceramic rings helps and encourages build up of useful bacteria, which in turns converts harmful substances, like ammonia, to enhance quality of the aquarium water.
The ceramic rings can be used with all types of filtration system and in conjugation with other filter mediums, like sponge and activated carbons. (however activated Carbon may affect the potency of medicine and therefore while administering medicine, it is recommended to remove activate carbon to attain desired affect / impact of the medicine)
It is a high performance ceramic rings even in small quantity.
Simultaneous breakdown of nitrites and reduction in nitrites.
Healthy fishes and plants.
No emission of harmful substances.
Fewer water changes.
Can be used in most filters-both fresh and saltwater.
This product is suitable in almost all filter, both in fresh and saltwater aquarium. Briefly rinse the bag holding the rings under running water (it is recommended to use aquarium water and not Tap water for this purpose). Place the ceramic rings inside the filter or under the gravel filtration system.
Please note the formation of the useful bacteria is a long drawn process and patience is recommended. You could also add bacteria into the aquarium to expedite the process of nitrification.
Canister filters are ideal filtration system for an aquarium. Though expensive, they maintain near ideal aquatic environment with little or no outside effort.
You need not carry out regular changes post installing external canister filter.
It is equipped to carry out Chemical, Physical and Biological filtration.
Ideal for 350-400 liter aquarium.
In addition this Canister filter has UV tube, which kills harmful bacteria and other pathogens, thus providing for extra protection for aquatic life.
Installation / User Guide:
According to the diagrammatic representation provided with the product, the buckle (1) and (2) should be unfolded at first, which will separate the main body and barrel-head.
Put the draining skeps with filter medium into the main body and turn, pressing the barrel-head. Then fasten the buckle (1) and (2).
Pull the securing buckle to take out the input and output discreteness. After this, the input and output pipes should be installed and they have to be fastened by nuts. Later, put the input and output discreteness to the former place and press the securing buckle to fix the input and output discreteness.
According to the diagrammatic representation, install the input and out curvy bar in the aquarium. (Notice! the curvy bar with spray bar is output curvy bar, and the curvy bar with dirtiness entrance is input curvy bar.)
According to the diagrammatic representation, press the blue buckle forcibly and leave it immediately. The blue buckle will rebound. and the input bar absorb water into main body at the same time which compel the air out of main body through output bar. When the level of water in output bar is equal to the level of aquarium, you may electrify the equipment to make it work.
Things under the transparent cover are control switch of UV light and indicator light of electricity. (Please bear in mind that life of UV light tube may vary due to various factors and may even seem fine, but it doesn’t mean the UV light is working or functional, when the equipment is working. So it is necessary to check the UV light regularly.)
The Method of Replacing the UV Light Tube :
According to the diagrammatic representation, you should loose the six bolts to separate the barrel-head and the cassette mechanism.
According to the diagrammatic representation, separating the contact of electric wire.